10 Common Boat Electrical Problems and What to Check
Here are some basic things to look for and test when you're having issues. Knowing the basics can save a trip or vacation, and being self-sufficient lets you better enjoy your time on the water!
Wire Corrosion

The connections that cause the most trouble are the ones you never see. Splices buried in a wire bundle, terminals behind a panel, and connectors tucked under a hatch or down in the bilge sit in damp air every day and rarely get inspected. Salt air alone is enough to start corrosion, and a slow leak from a deck fitting, hatch, or window can drip on a connection for years before anyone notices. Open terminals and connectors without adhesive lined heat shrink let that moisture wick between the jacket and the strands, where corrosion eats away at the copper while the outside still looks fine at a glance. When you are chasing a problem, check the hidden spots first: under the helm, behind the electrical panel, in the bilge, and anywhere you see water staining.

We cut this wire open and found the strands green with corrosion inside a jacket that looked fine from the outside.
We use and recommend marine grade heat shrink terminals for almost everything. Some people only use them in places with the risk of getting wet, but the reality is that a boat is a moist environment, and there are no parts of a boat that aren't affected by the humidity in the air.

The heat shrink on this lug was not adhesive lined. Water got into the connection and corroded the crimp and the wire underneath.
Corrosion is not just a reliability problem. Corroded strands add resistance, and resistance turns current into heat. That heat can melt insulation and start a fire, often without ever tripping a breaker or blowing a fuse.

Saltwater made its way into this wire. The corrosion added resistance, the resistance created heat, and the heat melted the insulation along its length. This is a major fire concern.

Corrosion caused this fuse to melt, but it never blew. A fuse only protects against too much current. It cannot protect you from a corroded connection heating itself up.
Electrolysis (electrolytic corrosion)
Normal corrosion takes years. Electrolysis can destroy a terminal in a single season. When a fuse holder, bus bar, or terminal block gets wet while it is energized, current starts flowing through the film of water between the terminals. That current pulls metal off the terminals and eats them away far faster than salt air alone ever could.
We find this most often on gear mounted low in the bilge, under leaking hatches and deck fittings, and in lockers that collect water. Look for green or white crust, pitted or thinning terminals, and fuse holders that have started to discolor.
The fix is to stop the water first. Mount electrical components high and dry, track down the leak, and use covered fuse blocks and bus bars. Once a component has been eaten by electrolysis, replace it. Cleaning it up only hides how much metal is gone.

This Maxi fuse holder was exposed to salt water. With current flowing through the wet holder, electrolysis ate away at the terminals.

Bus bars need to stay dry, too. This one sat wet while energized, and current running through the moisture corroded the plate and every screw on it.
Chafing
A boat never stops moving, and neither does the wiring inside it. Wherever a wire rubs against a sharp edge, a bulkhead, a hull stringer, or a hole with no grommet, vibration slowly wears through the jacket. Once the jacket is open, you either get a short or you let moisture into the copper.
Check where wires pass through bulkheads, run near the engine and steering gear, and sit under hatches or gear that gets moved around. Protect those spots with grommets, split loom, or chafe guard, and support wiring along its run. ABYC calls for conductors to be supported at least every 18 inches.

Chafe opened up the jacket on this speaker wire. Over time, salt air corroded the strands inside, even though the wire never sat in water.
Poor crimp and lug connections
Most of the failures we find are at the connections, not in the middle of a wire. A crimp is only as good as the tool, the terminal, and the person making it. Pliers, hammer crimpers, the wrong size lug, or careless stripping all leave you with a connection that looks finished but is not.
Every strand that gets cut while stripping or crimping is copper that can no longer carry current. The remaining strands work harder, the lug gets hot, and the connection gets worse each time it heats and cools. On a battery cable, that is a fire risk.
Give every connection a firm tug test, look for missing or broken strands at the lug, and watch for discolored or shrunken heat shrink near the terminal. Use a proper ratcheting crimper for small wire, a hydraulic crimper for battery cable, the correct size lug for the wire, and adhesive lined heat shrink over the finished crimp.

A bad crimp. A significant number of strands were cut during the crimping process, leaving far less copper to carry the load.
Voltage drop
Voltage drop happens when resistance somewhere in a circuit uses up voltage before it reaches the device. Corroded terminals, damaged or undersized wire, loose connections, and worn switches or breakers all add resistance. The symptoms look random: lights that dim or flicker, electronics that reboot, pumps that run slow, and engines that crank weakly even with a fully charged battery. Most of the time the device is fine. The wiring feeding it is the problem.
To find it, measure voltage at the device while it is running and compare it to the voltage at the battery. ABYC allows no more than 3% drop on critical circuits like navigation lights, electronics, and bilge blowers, and 10% on less critical loads. If you are losing more than that, something in between is adding resistance. Work from the battery toward the device, measuring at each connection, fuse, breaker, and switch, until you find where the voltage disappears. A bad connection can pass a continuity test and still drop several volts under load, so always test with the circuit running.

This cut wire was hidden inside a wire bundle and caused voltage drop between the starting battery and the engine. Testing voltage at each connection is how you find problems like this.

Salt water made its way into the back of this connector. As the pins corroded, resistance climbed until they lost continuity completely.
Tripping breaker
Immediately when switched on - probably a short somewhere along the wire. Inspect the wire carefully at both ends first. Then with the device disconnected, use a multi-meter and check for continuity between positive and negative. Inspect the length of the wire, look for chafe or anything that could be bridging positive and negative. Disconnect wire from load side of the breaker, and flip the switch. It could be a bad breaker. If the breaker trips when disconnected, replace the breaker. If the wire, breaker, and connections pass testing, chances are the problem is the device itself.

Breakers fail too. This AC breaker kept tripping because the studs had separated from their solder connection inside the breaker, a manufacturing defect. Nothing was wrong with the wiring or the load. From the outside it looks perfectly fine, which is why you test the breaker instead of trusting it.

Often, we see new installations that weren't carefully planned and end up damaging existing wiring. Always check behind that bulkhead when you are mounting the new device or drilling holes.
Batteries draining when away from the boat
If your batteries are going dead in a week or two while you are away from the boat, and you have turned the main battery switches off, something is still drawing power. Usually that means devices wired directly to the battery, bypassing the main switch. Check the positive terminals on each battery and the battery side of the main switch.
The only things that should be connected there are safety items: bilge pumps, smoke detectors, carbon monoxide detectors, and a boat monitoring system that can alert you to high water, low battery voltage, or loss of shore power.
One of the most common causes we find is an inverter left in the on mode. Even with nothing plugged in and no load on it, an inverter that is switched on draws a significant amount of power just to stay ready, and that parasitic draw can flatten a battery bank in days. Turn the inverter off when you leave the boat.
Some loads have to stay on, and that is fine as long as something is putting the power back. A properly sized solar panel and charge controller can offset the bilge pump, monitoring system, and detectors while the boat sits, so you come back to full batteries instead of dead ones. Our Marine Solar Design Guide walks through sizing a system for your boat.
If nothing beyond those safety items is connected and the batteries still drain, they may be getting tired and need care or replacement. Check the water level if they are flooded batteries, or let us come out and test them with our specialized equipment.
Wire nuts
Wire nuts are perfectly fine to use on land, but they are one of the cardinal sins in marine electrical work.

There are two major reasons that you should never, ever, use wire nuts.
They are designed for solid wire. Home wiring uses solid wire, meaning each conductor is one thick strand. When you twist two solid wires together with pliers, that is a fairly solid connection by itself, and the wire nut cuts tiny threads into the twist to lock it together. That works in a house because the wire never moves once it is installed.
A boat never stops moving. Engine vibration, wave impacts, and the hull flexing bend the wiring back and forth thousands of times a day. Every time copper bends, it work hardens a little, getting stiffer and more brittle. Solid copper wire cannot spread that bending out, so the strain concentrates right where the wire is clamped or twisted. Tiny cracks form, they grow with every cycle, and eventually the wire suffers a fatigue failure and snaps, often hidden inside the connector where you cannot see it. That is why ABYC requires stranded wire on boats. Each thin strand bends with far less strain than one thick conductor, so stranded wire can flex with the boat for years without breaking.
Stranded wire needs connectors made for it. A wire nut screwed onto stranded cable does not bite the way it does on solid wire, the connection is usually poor from the start, and the chances are very good that it will eventually come apart.
There is no water resistance. Going back to the first item on the list - high quality marine heat shrinks connectors - stop moisture from entering the connection altogether. Wire nuts do no such thing, and in a home do not need to.
Overloaded terminals
This is an issue we see on the majority of vessels we work on. Instead of using a bus bar connected to the battery, people just connect wire after wire directly to the battery posts. Maybe there IS a bus bar, but there are just so many wires that the bus bar ends up overloaded as well!

According to ABYC (American Boat & Yacht Council), no more than 4 connections are allowed per terminal.
Check your batteries, bus bars, circuit breakers, and any other terminals for this. While you're at it, make sure that the biggest connectors are on the bottom, and the smallest on the top. Large connectors = high amperage. Small connectors cannot handle that kind of amperage, and can melt/catch fire!
Stainless washers between battery terminals and cable lugs
Stainless steel is great for hardware and terrible at carrying current. It conducts only a small fraction as well as copper. When a stainless washer is placed between a cable lug and the terminal it is bolted to, all of the current in that cable has to pass through the washer, and the connection turns into a heater.
The cable lug should always sit directly on the terminal surface. Washers, lock washers, and the nut go on top of the lug, never underneath it. This applies to battery posts, fuse holders, bus bars, battery switches, and any other high current connection. Check every heavy cable connection on your boat. Discoloration, melted plastic, or a lug that is warm to the touch after a heavy load are all warning signs.

A stainless washer was put underneath the battery cable on this MRBF fuse holder. The connection heated up and scorched the holder. This is a major fire risk.